How to remove camera blur on your phone. How to clean a video camera lens

Cleaning your camera is a very important task. Dust, dirt and moisture can have a detrimental effect on your expensive equipment, so it pays to keep everything in good condition. Below is a 5-point camera cleaning checklist that every photographer should read...

Spending a little time cleaning your camera's sensor will save you a lot of time cloning the good parts of the photo for the dust marks. It's also worth checking your lenses and other pieces of equipment to ensure you keep everything in good working order.

It's also worth checking your camera's software. If it is up to date. Therefore, the final check item on this list would be updating the camera's firmware.

How often you'll need to check each item will depend on how often you use the camera and the conditions in which you're shooting. If you take photographs regularly, then you should go through the main points of this list about once a month.

1. Camera body

Problem

Dirt and dust on the outside of the camera may not seem like a big deal, but it can get into the camera, either the sensor (see point 3) or numerous mechanical or electrical components that can cause more serious problems.

So it's worth cleaning your camera every few months - or more often if you're shooting in really bad conditions.

Solution

Start with the lens or body cap attached to the camera to prevent dust from getting inside the camera. Go over with a brush or blow off the worst areas of dirt and dust.

Pay special attention to the most uncomfortable areas. Areas around the lens mount, viewfinder, etc.

Once the dust has been removed, you can use a soft cloth to remove stubborn stains, either on the body of the unit or on your LCD.

You can also use Q-tips to get into any hard-to-reach nooks and crannies.

If the dirt is very stubborn, lightly dampen a cloth or cotton swab in distilled water before cleaning.

Finally, you can remove the lens and protective cap and carefully clean the inside of the camera. You must be careful to do this so as not to touch any of the mechanisms inside the camera.

Also, make sure you hold the camera with the lens opening facing down. This will minimize the risk of dust entering the camera again. You can use a blower to remove dust from the mirror section.

2. Lenses and filters

Problem

Dust, dirt or water stains on the lens or filter can cause blur to your photos, so you'll need to clean them regularly, especially if you're shooting in bad weather or dirty locations.

Solution

Cleaning the lens is similar to cleaning the camera body, but in this case you must be especially careful not to scratch the front and rear optics.

Again, brush or blow away any dirt, dust or sand so that it doesn't scratch the lens when cleaning the glass itself.

Once you are satisfied that any dirt or sand has been completely removed, you can use wipes or a suitable cloth to wipe down the lens glass.

You may need to resort to more specialized lens cleaning methods to clear stubborn dirt. If so, place a few drops of detergent on a cloth (never on the lens itself!), then wipe the glass surfaces thoroughly.
Finally, use a clean cloth to wipe away any residue.

To check the surface of the lens, position the lens so that you can see the reflection of light from a window (or similar light source) on its surface.

This will help show you any residue or marks that may be causing blur. You can also clean any filters using the same methods, but you must be especially careful if you have resins on the surface of the filter, as these filters are often more prone to scratches than glass filters.

3. Matrix

Problem

Dust and dirt can easily get into the camera and cause blemishes on your images. This is especially noticeable if you shoot at small apertures and with wide-angle lenses.

Solution

Cleaning the inside of your camera must be done with great care and the right tools, otherwise you may end up doing more harm than good. The cleaning itself is quite simple.

First of all, you need to lock the mirror in your camera's cleaning mode, which is usually found in the setup menu of most cameras, and then follow the instructions for your camera to activate this feature.

Then you need to remove the lens and hold the camera so that the lens opening points slightly downward.

For basic cleaning, use the same blower to remove dust and dirt.

Don't be tempted to use an aerosol can, as they contain flammable ingredients that can get into the camera - plus they're also very strong and can damage the delicate mechanisms inside the camera.

For more stubborn dirt, you can use a brush like the Arctic Butterfly.

If there is water splashing or condensation, you need to:

1. Use a damp swab.
2. The tampon must be the correct size for your matrix and you must follow the instructions carefully.
3. Pour one or two drops of a special cleaning solution onto the swab.
4. Gently rub it over the sensor in one direction and then back in the other direction.

Resist the temptation to wipe the sensor again, as dust or dirt collected during the first pass will fall back onto the sensor.

After each cleaning, you can check whether dirt has been removed by photographing a blank sheet of white paper at a small aperture, such as f/22. Then carefully check the image on your camera's back screen for dust spots (or on your computer monitor, that would be even better).

If there are still spaces, repeat the procedure using a new tampon - do not reuse them for the reasons stated above.

You already know how to care for your camera. Now we invite you to read the article in which you will learn what mistakes advanced and novice photographers make while on vacation.

4. Accessories

Problem

Even if you keep your camera and lens clean, it's all too easy to forget about the more mundane things. Dirt and dust in your camera bag can find its way into your camera. Tripod locks and adjusters can become locked if they are always left wet or dirty.

Solution

Although accessories aren't as thin or fragile as a camera or lenses, almost every piece of photography kit can benefit you if you keep it clean.

For most items, an occasional brushing or just making sure they are clean will be enough. But there are a few accessories that often go unnoticed.

The first is your tripod. This is a piece of kit that very often spends its time in mud, water or sand, especially if you're shooting on the coast or other harsh conditions.

If this is the case for you, then you may:

1. you will need to wash the entire tripod in clean water;
2. then, to reduce the risk of corrosion, use a small amount of water-repellent lubricant;
3. do not overdo it with lubrication, as this may cause more problems than it solves;

Finally, it's worth taking a look at your bag, as even though a dirty or dusty bag may not have a direct impact on the quality of your photos, dust can get onto (or even into) the camera.

5. Software

Problem

Like many other computer programs, the camera's operating system (known as "firmware") can be updated to install new features and even solutions to operational problems, so it's worth making sure your camera's OS is up to date.

Solution

First of all, you need to check the firmware version that is installed in the camera. This can usually be found by going to settings and scrolling to the firmware menu.

It could be one number, such as 1.00 or 1.02, or there could be two or three number/letter combinations.

Next, go to the camera manufacturer's website and try to find the latest firmware available for your camera.

If a later version is available than the one installed on your camera, you need to:

1. download this firmware to your Mac or PC;
2. copy it to a formatted memory card that will match your camera;
3. insert the card into the camera;
4. go to the firmware menu and follow the instructions to update it.

Once you're done, you need:

• turn off the camera;
• remove the card;
• then turn on the camera again and make sure that the installed firmware version matches the version downloaded from the website;

We hope now your equipment will always be clean!

In this mobile age, every person has several touch screen devices, be it a mobile phone or a tablet. But after a while, small and sometimes large scratches appear on any touch device. If the cracks are large enough and you notice that this has led to the loss of some functions or malfunctions, be sure to replace the glass or display. But if there are only small scuffs on the screen, you can deal with it yourself. How to remove scratches from a phone camera - this is what we will discuss in this article.

Preparation for polishing

Before you start polishing, it is necessary to carry out preparatory work:

1. Turn off the device completely.
2. Cover the external connectors with masking tape or electrical tape. This will prevent water and other foreign substances from getting inside the gadget.

Important! Be patient, you may have to spend a lot of time getting your gadget in order.

Paste GOI

It is unlikely that you will be able to completely get rid of scratches, but they can be disguised. This can be done by polishing. How to remove scratches on a phone camera and polish the display?

You can use a product called GOI paste. It comes in several types, depending on the grain size.

Important! The finest paste is suitable for polishing the display. Machine oil won't hurt either. You only need a few drops to dilute the GOI paste.

Operating procedure:

1. First, clean the screen of dirt, otherwise you will not be happy with the result.
2. Take a woolen cloth, rub it with paste and add a drop of machine oil.
3. Rub the resulting mass into the display using the same woolen rag.
4. You need to polish until the scratches become barely noticeable, if you're lucky, they won't be visible at all.

Polishing with toothpaste

How to polish your phone camera using toothpaste? For these purposes, you will need regular white toothpaste, without any additives in the form of crystals or granules:

1. Apply some toothpaste to the scratched surface. You can polish using a piece of soft cloth, a cotton swab or a special microfiber cloth.
2. Rub the product in circular motions for several minutes.
3. Remains of toothpaste can be removed after polishing with a slightly damp soft cloth.
4. If the result does not impress you, you can repeat the procedure.

Polishing with baking soda

In the same way, you can polish the surface using baking soda, which is available in the kitchen of any home:

1. Dilute the baking soda with a small amount of water until you get a paste.
2. Apply this mixture to a soft cloth or napkin and buff the surface with gentle movements.

Important! Try not to press too hard on the surface so as not to aggravate the defect.

How to remove scratches with polish?

First you need to purchase a special polish. The product must contain cerium oxide. You can buy polish either ready-made or in the form of a substance that must be dissolved before use. The first option is much more convenient to use, however, soluble powder will ensure high quality polish.

Operating procedure:

• Prepare polish. If you bought it in powder form, then it must be dissolved. Follow the instructions. Pour the specified amount of polish into a bowl, gradually adding water and stirring the resulting mixture.

Important! Under no circumstances should this product come into contact with places such as the phone speaker, charger hole, or headphone jack. In addition, it is quite dangerous for a smartphone camera. Therefore, if you want to remove scratches on your camera, you need to use it very carefully or choose a different polishing method.

• Now you need to rub in the polish using a cotton rag or cotton swab. The surface should be treated until the damage disappears or becomes significantly smaller.
• After finishing polishing, be sure to remove the excess with a dry cloth or napkin.

Vegetable oil

Vegetable oil can provide timely help for your device. True, it is used rather to give the surface a beautiful shine, and small scratches will become less noticeable. Just drop a drop of oil onto the screen and rub it with a dry soft cloth.

Professional products

There are also professional products for polishing gadget screens on sale. The most popular product is DISPLEX DISPLAY paste, a completely new type of polishing paste that does not contain abrasive elements. The procedure for removing scratches and abrasions is done quickly.

Important! When used correctly, the contents are enough for 8-10 polishings - it all depends on the area of ​​the surface being treated.

DISPLEX paste does not contain abrasive elements; after using this product, the display does not become cloudy. There is only one significant drawback - the rather high price.

Important! If you were unable to restore your camera, but you use it constantly, it makes sense to think about buying a more advanced device. Check out our rating.

Preventing scratches

How can you protect your phone camera and display in general from scratches?

Six months ago, I noticed a problem in pictures taken on my iPhone. Different photographs were marked with a spot in the same place in the frame. Having carefully examined the glass above the microscopic camera lens, I found a small speck of dust and removed it by tapping the body with my hand.

After some time, there was so much dust that it became physically impossible to take normal pictures. I turned to a specialized service to not only fix the problem itself, but also to find its underlying cause. As it turned out, the matter could not be limited to simply cleaning the glass. Over the past year, a lot of dirt has accumulated inside, and your situation is most likely no different from mine for the better! You just don't know about it yet.

For answers to my questions, I turned to the MacPlus.ru service. The guys were invited to their workshop to show and tell where the dust inside the case comes from and how to properly remove it. Homemade tools are not suitable for this at all. Neither cotton swabs, nor, especially, a vacuum cleaner pipe will lead to the best results. Before this, I gave my smartphone twice to “home-grown” craftsmen, and each time after that the dust appeared again, literally after a few days.

A master named Alexander began the process methodically: this is not the first time they have had a device with such a problem, not the tenth, or even the fiftieth. Not much changes from generation to generation of Apple smartphones: the iPhone was never completely sealed, and therefore the pristine purity of its internal components is only a temporary phenomenon.

We're dealing with an iPhone 5, which means the disassembly process starts with unscrewing the bolts next to the Lightning port. These microscopic screws are as easy to lose as it is difficult to find an ordinary screwdriver for them. By the way, we are dealing with the standard , and its special variety TS1. To do this you will have to purchase a special tool.

But then comes an important point that allows you to distinguish a real professional from a “home-grown” expert who learned on roller skates with YouTube. Under no circumstances should the display be disconnected from the main part using a suction cup. Careless use of force leads to the detachment of glass from the display module, which turns the entire “sandwich” into a less useful set of hardware. If one day after repairs you notice that streaks or tiny bubbles have appeared under the glass above the screen, you are faced with the work of an amateur.

We lift the screen module and see an extremely sad picture. I've been using my smartphone for a little over a year, but I've never placed it in dusty places, hidden it under a dusty pillow, or kept it in my jeans pocket for long periods of time. But somehow the dust has accumulated, and it’s not just a lot of it. If I were the master, I would have grinned, but, as it turned out, all this is an absolutely ordinary picture. The only difference is that someone is lucky and the dust does not get on the glass above the camera module longer.

To assess the full extent of dust contamination, the electromagnetic protection is removed from the iPhone 5 motherboard. It also partially stopped the spread of particles. As luck would have it, the outbreak fell on the camera, and it didn’t just happen.

According to the technician, the problem could have appeared after the smartphone fell onto a hard surface. In such cases, the relative tightness of the rim around the screen could be compromised. And slowly, particle by particle, the entire upper, inner part of the body was filled with dust. So why did previous calls to other service companies not bring the desired results? It's just that the cleaning was most likely done manually.

All bolts and elements of the smartphone are placed in a tray with cells. Losing any of the spare parts is disadvantageous, first of all, for the mechanic himself: a second such spare part is not always available. God forbid you lose any of this at home, not to mention damage to some cable. And there are a lot of trains here.

Having removed all loose elements, Alexander takes a powerful air blower powered by a compressor. Without such a thing, it is almost impossible to get rid of dust in the case. By intelligently adjusting the air flow, you can remove all the dirt from sensitive electronic components without damaging any of them. The process takes almost a minute. Immediately after this, the smartphone looks like new - compared to what it was before. But we're not done yet.

Since dust has probably gotten on the optics in the camera, you will have to carefully clean them too, and at the same time go over the glass inside with a cotton swab. Pay attention to the size of the flash: its power, sufficient to illuminate dark rooms as a flashlight, does not in any way correlate with the microscopic size of the module. And there is also a lot of dust on it. Time for handmade work, and very careful work at that.

After walking with a cotton swab along the inner wall of the back of the case, the master begins assembling the smartphone. The parts fit into place in the reverse order, carefully and without haste. Trembling hands are the most terrible enemy in this matter. Calmness during this process makes the difference between a barely noticeable “click” of an inserted cable and a broken pad.

The iPhone was dirty and dusty. It became clean. The whole thing took about 5 minutes. The remaining fifteen I looked at the “insides” of the device. Say what you like, but only Apple knows how to make hardware as well as the design of the case. Black motherboard, strictly arranged main chips, incredible density of components per millimeter. Alexander also agrees: other manufacturers almost always ignore everything that is not visible to the average user. It is for this attention to detail that we love the products of the Apple company.

It all started with two bolts, and it all ends with two bolts. The screws are put into place, the smartphone is turned on and the camera is checked. In principle, this is not necessary. Just look at the camera again and see the huge difference.

Many of us are the proud owners of cutting-edge smartphones with touch screens. However, not all owners of these gadgets know how to handle their property with care. Therefore, over time, small scratches begin to appear on the screen. In this article you will learn how to polish the glass on your phone.

What will be required to perform the manipulations?

You can try removing scratches from your smartphone display using regular toothpaste. It is prohibited to use abrasive powder for these purposes, since the microparticles it contains can damage the screen.

Before polishing the glass on your phone, you need to stock up on soft wipes and a special liquid designed to clean touch screens from microdust and plaque. It is sold in many stores. If this liquid is not available, you can do without it.

Procedure

Before polishing the glass on your phone from scratches, you need to carefully wipe the display. This can be done in a circular motion using a soft rag or a special napkin.

After this, you need to take a clean cloth and, after applying a little toothpaste to it, put it on. After a couple of minutes, you should wipe the entire surface of the screen and polish it with a clean cloth. After completing the procedure, you can wipe the display with cleaning liquid. As a rule, after this all microscopic scratches disappear, and deeper ones become less noticeable.

Professional products

Those who want to figure out how to polish the glass on their phone will be interested in another method. It allows you to remove scratches without leaving a trace without visiting a specialized workshop. To do this you will need GOI or Displex paste. These professional formulations are sold in many communication stores.

Apply a small amount of one of the above products to the display and rub gently in a circular motion using a soft cloth. After the defects have been completely eliminated, the remaining composition must be removed.

Car polishes

There is another, no less effective way to polish scratches on your phone glass. To do this, you will need a special composition designed for car care. Such products can effectively remove defects without damaging the surface itself.

For processing you will need a soft rag and the polish itself. First, you need to apply a small amount of product to the screen. After this, the display is wiped with careful circular movements.

Removing shallow scratches with baby powder

This technique allows you to effectively eliminate small abrasions and minor defects. How to polish phone glass at home? First you need to prepare a polishing paste based on a product that is intended for caring for children's skin. The talc present in the powder will act as a gentle abrasive.

A small amount of dry powder must be diluted with a few drops of water and mixed until a homogeneous mass is obtained. This composition is applied to the screen and rubbed with a soft cloth. At the end of the procedure, remove excess product with a damp cloth.

Baking soda

Almost every housewife has this multifunctional product in stock. It can not only be added to baked goods, but also used for other purposes. The abrasive particles contained in soda perfectly smooth out unevenness on the surfaces being treated.

How to polish the glass on your phone using this ingredient? You need to prepare a special composition. To do this, mix one part baking soda with two parts water. As a result, you should get a homogeneous paste. Apply this mixture to a piece of soft cloth and wipe the touch screen with it. You can use a damp cloth to remove any remaining product.

During the process, it is important to ensure that the rag used to remove excess soda is only slightly moistened with water. Excess fluid can cause other, more serious problems.

Nowadays there is a photo and video camera on almost every modern phone. On some there are even two of them: back and front. On more expensive models, for example, the iPhone 6, the camera allows you to take very decent pictures of excellent quality. But after a while, you may realize that the photographs taken have become unclear. The most common culprit for this is dust and dirt on the lens. Why be surprised? Where do you usually carry your smartphone? In a jacket or jeans pocket, in a bag, backpack or briefcase. Therefore, the time comes when you need to clean your phone camera from dirt.
The best tool for this is a regular microfiber cloth. But, unfortunately, it is not always at hand. You can replace it with a clean and slightly damp cloth or soft cloth. The main requirement is that it is not wet and does not leave lint on the lens.

Another convenient tool that allows you to clean the camera of an iPhone or any other phone is a simple cotton swab, which is always in the “arsenal” of almost any modern representative of the fair sex. But it’s better not to rub the glass with a dry stick. Moisten it a little with glass cleaner and squeeze thoroughly. It should be just a little damp. The main thing is that you don’t even think about spraying glass cleaner on your phone, tablet or smartphone.

Do not clean the lens with dry, hard rags, paper handkerchiefs or toilet paper. Hard surfaces and various particles can easily scratch the glass of the rear or front camera.

P.S. If dirt and dust get inside, under the glass, then in this case you will have to completely disassemble the device. This is a more complex and time-consuming process. Therefore, I would not recommend cleaning the lens and glass from the inside on your own - it is better to seek the help of specialists.